← Back to The HUT

April 1983 · Vol. 19 No. 4

April 1983 Magazine (Vol. 19 No. 4)

Issue first-page cover

Magazine · 20 pages

April 1983 Magazine (Vol. 19 No. 4)

Captured text — scan page 4

Automatically captured text may contain recognition errors. Compare it with the original scan.

CLIFF’S CORNER

Bob Brown, Darrell Foss and I have built
more than a dozen woodstrip canoes. Yet only
recently have we gotten our act together on
how to fiberglass. Over the years we've learned
a lot about durability, delamination, strength
. .- and what not to do! Hopefully, interested
builders ean learn from our mistakes.

Our earliest boats were constructed with
a layer of 72-ounce cloth outside and a layer
of 4-ounce cloth inside. We used MCA polyester
resin and had few problems. Our glassing pro-
cedure was:

1. Sand the hull thoroughly with an orbital
sander with 60 grit paper.

2. Set the glass cloth (wrinkle-free) over the
sanded hull and apply "finishing" resin (resin
with wax mixed in) to the cloth with a
short-napped paint roller.

3. After the resin is rolled on, apply a second
coat of "hot mix" resin to the glass with
the roller. This step should fill the weave
of the fabric.

4. Allow the resin to cure thoroughly, then
sand and varnish.

We encountered few problems with this
procedure, save for an occasional small starved
area.

Then we got the idea that using two layers
of 4-ounce cloth outside would be better than
a single layer of 7z-ounce stuff. Glass to resin
ratio would be higher and the tight weave of
_the cloth should result in a quicker and easier
high final finish.

So we tried it. We glassed three canoes in
this manner according to the procedure above.
The results were disappointing. Every canoe
exhibited resin starved areas. In fact, I nearly
burned "Mantoy" (the CJ solo prototype) because
it looked so bad. Only soothing encouragement
by Bob and Darrell enticed me to finish the
boat—which paddled so well I kept it.

I learned that durability of the double
4-ounce glass was actually less than one layer
of 72 ... even less than a single layer of 6-
ounce (according to Gene Jensen). The light-
weight glass slit like paper on sharp rocks.

It did make for a structurally strong and stiff

lightweight boat, but that was all. A heavier

weave was needed to combat abrasion.

ONG LI

& Ye,, HANDCRAFTED CANOE
€s PADDLES

BENT SHAFT $41.95

Custom Canoe Paddles STRAIGHT SHAFT $37.95
(SHIPPING NOT INCLUDED)

1076 EDMUND AVE. ST PAUL. MN $5104 612-645-9453

4 HUT!

Darrell recently completed a 12-foot
solo canoe of his design using the "Jensen
method." Perfect! We heartily reeommend
the procedure. Dry wood must be primed before
glassing to prevent the occurrence of starved
areas!

While Darrell was experimenting, I tried
WEST Epoxy. I had just completed a beautiful
142-foot solo boat designed for me by Bob
Brown. The western red cedar hull was gorgeous
and the evolved design suggested the boat would
be a magnificent cruiser. I decided to take a
chance on the 52-dollar-a-gallon epoxy.

But I was concerned about the epoxy-
related horror stories—rashes, respiratory and
physical disorders. The WEST literature
stressed the low toxicity of the product but
did advise wearing barrier cream and gloves.
No mention was made of using a "respirator."

I ealled Lew Miller—president of Rice Creek

Boat Works. Lew had built dozens of epoxy

boats and was a great believer in the stuff.

"It's safe," said Lew. "I've used it in my base-

ment!"

Now... after using the product ['m-most
enthusiastic. It's nearly odorless and foolproof.
It sands almost as easily as polyester but has
much superior abrasion and peel strength.
Unique, is a clever pump which meters out
precise quantities of the resin with no waste
or spillage. It's trouble-free—no delamination,
no starvation, and high flexibility. I doubt if
I'll build another polyester boat.

Using WEST epoxy is similar to glassing
with polyester with these exceptions:

1. Roll ona prime coat with a foam roller.

2. Sand the hull lightly after the prime coat
cures.

3. Place the glass on the primed and sanded
hull and squeegee on the epoxy. Don't
use a roller for this operation; it traps
too much air which may cause a cloudy
finish. The flexible plastic squeegees that
are recommended work great.

4. After eure, sand (electric drill with 80-
grit disk) the top few microns of cloth
and resin—enough to get a reasonably
smooth surface.

5. Roll on (foam roller) enough epoxy to fill
the fabric weave. Allow to cure.

6. If the weave is completely filled you may
sand and apply two coats of varnish which
contains ultraviolet inhibitors. If the weave
is not filled, sand again with the electric
drill and apply a leveling coat of epoxy.

‘7. Stand back and admire your work. You've
done a perfect job! Cliff Jacobson a

Articles (13) · Summaries (13)

Generated issue overview: April 1983 issue of HUT!, the monthly newsletter of the Minnesota Canoe Association. This issue includes canoe-building and conservation articles, forest canoe-route information, trip reports, chapter news, and calendars and event notices.

Generated summaries are descriptions, not original captured text. Page-range text shows complete scan pages and may include neighboring material.

Superior National Forest

Title transcribed from original publication

Generated summary: Provides information for canoeists traveling in the Boundary Waters Canoe Area Wilderness, including permit requirements, bear precautions, health and safety guidance, and Forest Service contact information.

Open scan page 1

Read captured pages 1–16 →

Chippewa National Forest

Title transcribed from original publication

Generated summary: Describes canoe routes in and near the Chippewa National Forest, including the Inguadona, Turtle, and Rice River tours, and gives route, camping, water-condition, and safety information.

Open scan page 1

Read captured pages 1–18 →

Cliff’s Corner

Title transcribed from original publication

Generated summary: Discusses fiberglassing woodstrip canoes, comparing cloth weights and polyester resin with WEST epoxy, and gives a step-by-step epoxy procedure.

Open scan page 4

Read captured page 4 →

Conservation

Title transcribed from original publication

Generated summary: Announces an MCA and DNR project to inventory river conditions and collect reports on water levels and canoeing conditions for a public river-reporting service.

Open scan page 5

Read captured page 5 →

The Survival of the Bark Canoe (Book Review)

Title transcribed from original publication

Generated summary: Reviews John McPhee’s book about bark-canoe maker Henri Vaillancourt, a Maine woods canoe trip, and an appendix of Edwin Tappan Adney’s canoe sketches and models.

Open scan page 6

Read captured page 6 →

Cruisin’ Along

Title transcribed from original publication

Generated summary: Offers early-season canoeing safety reminders about cold water, flooding debris, group awareness, and personal flotation devices, and asks for trip leaders.

Open scan page 6

Read captured page 6 →

Frozen Canoe Country

Title transcribed from original publication

Generated summary: Recounts a winter ski and snowshoe trip in the Boundary Waters with the American Lung Association’s Winter Wilderness Trek, describing the conditions, group, and experience.

Open scan page 7

Read captured page 7 →

Weekend Training Runs — Long Slow Days

Title transcribed from original publication

Generated summary: Describes spring training runs on flooded Minnesota rivers for canoeists, including their schedule, preparation, and contact information for joining.

Open scan page 13

Read captured page 13 →

Forest Service Needs Volunteers

Title transcribed from original publication

Generated summary: Describes volunteer opportunities with the Forest Service, including wilderness ranger, campground, trail, visitor-information, and other work, along with basic eligibility and support details.

Open scan page 13

Read captured page 13 →

Annual Rice River Paddle

Title transcribed from original publication

Generated summary: Recalls a family’s experience during the 1982 group paddle on Rice Creek and invites paddlers to join the 1983 outing.

Open scan page 13

Read captured page 13 →

Poor Betty’s Almanac

Title transcribed from original publication

Generated summary: A humorous column about canoe racers’ interests and activities outside racing, with anecdotes about several named racers.

Open scan page 14

Read captured page 14 →

St. Cloud Chapter News

Title transcribed from original publication

Generated summary: Reports the St. Cloud Chapter’s officer elections, meeting discussion, and planned cruises and outings.

Open scan page 14

Read captured page 14 →

Duluth Traveler

Title transcribed from original publication

Generated summary: Presents Duluth-area chapter contacts and a schedule of upcoming meetings, cruises, and whitewater trips, with details for participation.

Open scan page 14

Read captured pages 14–15 →