← Back to The HUT

December 1981 · Volume/issue not printed or unknown

December 1981 Magazine

Issue first-page cover

Magazine · 16 pages

December 1981 Magazine

Captured text — scan page 7

Automatically captured text may contain recognition errors. Compare it with the original scan.

This shows the complete scan page, including any other material on it.

2 4 Often, the plans have more than one column of num-
Buitdes bers for boats of differing lengths. Be sure that you
"5 use the right numbers for your boat. Transer these

dimensions carefully to your strongback and draw a
line across the strongback with a square at each

Corner dimension. It is a good idea also to label each line

as you make it.

As you begin to install your forms, you will begin to
by Bob Brown see the importance of the center lines that you drew

. on your forms.
You've picked your plan and are ready to go. Your

next step is to create a usable set of forms. I like to install my forms with the block toward the
. center of the strongback and the flat side of the
There are other methods of transferring plans, but my form just touching the line. When satisfied, drill and
preferred method is to use carbon paper and transfer serew them in place. Check for square before the
the plans to pieces of craft paper or poster board, second screw is installed.
making sure that you also transfer the plan's
centerlines. These pieces are then cut out and. you I like to use lag screws for this job along with a
have a set of patterns. large, flat washer, and I like to have two screws to a
. form. Lag screws may cost slightly more than slotted
I prefer to use chip board for my forms. I take my ones, but they are so much easier to install and
patterns and draw around the outside of them, remove that they are well worth the difference.
transferring my patterns to the chip board. Be sure
to draw the center line of your forms as this is very As you install your forms, check them for square both
important later. crossways and vertically. They should be close.
I like to lay out all of my forms before I cut any; Installing the end pieces is probably one of the most
this may save expensive mistakes. When all your critical parts of building the forms. These pieces
forms are drawn, it's time to start sawing. must be straight with each other. This can be done
. . . with a square, a level, or simply by some very careful
A band saw is great for cutting forms if you have eyeballing.
one. Lacking a band saw, I use my saber saw
followed by a 12" disk sander. I cut my forms The end pieces are installed straddling the center line
slightly oversize with the saw, then run the edges of your strongback and shimmed so they are square
over my sander cutting away material until the line - with each other. I haven't advised you to level your
just disappears. I repeat this operation on all of my strongback; it is not really necessary as long as the
forms. two end pieces are in line.
My next step is to cut out the end pieces. For this I After you are satisfied with the alignment of the end
use plywood. If you plan to leave the end pieces in pieces, it is time to stretch your chalk line again. I
your boat, I'd recommend that they be built out of at drive a small wire nail into the very top edge of each
least exterior grade plywood. end piece and stretch a line between. Raise this line
just high enough on the nails so the string clears the
After they are sawed, they need to be beveled as highest form. Again, the importance of the center
shown in your plan. As you sand into the plywood, lines that you drew on the forms becomes apparent.
the width of the plys will be helpful in gauging how The center lines of each form must match this string.
much material has been removed and where to cut
away mores ‘Any forms that don't match up to the string can be
. . moved with some shims. The bottom of the form has
If you plan to leave the end pieces in, they should be to remain centered on the strongback, but the top can
sawed off at this time. I like to start this cut, then be moved sideways quite a bit by installing thin shims
reattach it with staples even as it's being removed. under the 2x2 block near the side of the strongback.

: It may take several shims to correct really bad forms.
Now we need a method of fastening the forms to the

strongback. I have found that 6" 2x2 blocks fastened Now it's time to stand back and look over your work.

to the forms do just fine. These blocks should be Take a break and admire this form. See if it looks

mounted with care to get them just flush with the like the boat you expected.

straight base line on the form. .On the end pieces, I

like to have a back on either side. This helps to Before you start stripping, take a strip and get a

make it more stable on the strongback. helper who will help you hold this strip against the
. . side of your forms. This strip should lay flat against

The time has come to put the whole thing together. all the forms that it crosses (if the forms are right).

Set your strongback up on its legs and check it over You and your helper should move this strip around to

for any looseness or bends that can be corrected many different places checking out the fairness of

before installing the forms. your forms.

Take a chalk line and stretch it lengthwise on the A small error in the position of a form (an easy

strongback near the center. Snap this line, and you mistake to make) will have a disastrous effect on the

have a straight line to install your forms along. finished boat. It is best to catch these things before

. you start stripping. Any mistake in the shape of a

The measurements for setting up your forms can be form should also be noticed before the stripping is

found on the plan. These dimensions may be given as ready to begin.

the distance from the center form, or they may be an

equal distance apart and simply stated as "on 16-inch Next month, you get out the glue and staples and

centers" or "on 12-inch centers." 7 begin to make something that really looks like a boat.

Articles (21) · Summaries (21)

Generated issue overview: A December 1981 issue of HUT!, the Minnesota Canoe Association newsletter. It includes association news, canoeing and outdoor skills articles, trip and event information, winter recreation features, and member notices.

Generated summaries are descriptions, not original captured text. Page-range text shows complete scan pages and may include neighboring material.

Canoe Building with Bob Brown

Title transcribed from original publication

Generated summary: A short announcement describes the February program on woodstrip canoe building, presented by Bob Brown, and invites prospective builders to ask questions.

Open scan page 1

Read captured page 1 →

Telemark Clinic

Title transcribed from original publication

Generated summary: An announcement describes a three-day telemark skiing clinic, including instruction in equipment, safety, rescue, route finding, and skiing across different terrain and snow conditions.

Open scan page 4

Read captured page 4 →

Lessons & Clinics From the Bow

Title transcribed from original publication

Generated summary: The MCA president outlines planned 1982 member benefits, monthly programs, education and safety initiatives, and ways members can help shape the association.

Open scan page 4

Read captured page 4 →

The Season Warmup

Title transcribed from original publication

Generated summary: Members are invited to a February social gathering at the Hall Brothers Jazz Emporium, with a pre-party at John Wexler's home.

Open scan page 5

Read captured page 5 →

Minnesota Winter Wilderness Trek

Title transcribed from original publication

Generated summary: An overview of a February winter camping and cross-country skiing trip in the Boundary Waters Canoe Area Wilderness, including training topics, travel plans, and fundraising details.

Open scan page 5

Read captured page 5 →

Cross Country at the Zoo

Title transcribed from original publication

Generated summary: A personal account recommends the Minnesota Zoo's wooded, varied cross-country ski trails and notes opportunities to observe animals and visit the Zoo Lab.

Open scan page 5

Read captured page 5 →

MCA Education Committee Report

Title transcribed from original publication

Generated summary: The report describes the MCA's plans for structured canoeing instruction in 1982, lists proposed courses and coordinators, and explains materials and standards the Education Committee intends to develop for classes.

Open scan page 6

Read captured page 6 →

AI-supplied descriptive title: Plans for the MCA canoe-building program

AI-supplied descriptive title

Generated summary: The building director describes plans for canoe-building classes, a demonstration at Hoigaards, and opportunities for volunteers, instructors, and students to participate.

Open scan page 6

Read captured page 6 →

Builders

Title transcribed from original publication

Generated summary: A practical guide to making and aligning canoe-building forms on a strongback, covering pattern transfer, cutting and fitting forms, checking alignment, and inspecting fairness before stripping begins.

Open scan page 7

Read captured page 7 →

Glancing Back at Fall

Title transcribed from original publication

Generated summary: A photo-illustrated account recalls the October 4 Color Cruise on the St. Croix, describing the calm outing, participants, and Voyageur canoe crew.

Open scan page 8

Read captured pages 8–9 →

Boat License Sales Increase Again

Title transcribed from original publication

Generated summary: A brief report gives Minnesota's December 1981 watercraft registration total, category counts, year-over-year changes, and a per-capita comparison.

Open scan page 3

Read captured page 3 →

New Map Shows State Wildlife Lands

Title transcribed from original publication

Generated summary: A short news item describes a newly published DNR map of Wildlife Management Areas and public hunting grounds, and summarizes the program and funding behind land acquisition.

Open scan page 3

Read captured page 3 →

First Ice Breaking Cruise

Title transcribed from original publication

Generated summary: John Wexler outlines tentative plans for early-season whitewater runs, asks interested paddlers to keep possible dates open, and seeks experienced boaters for an exploratory river trip near St. Cloud.

Open scan page 3

Read captured page 3 →

The Ultimate Canoe Challenge: 17,900 Miles Paddle & Portage Completed

Title transcribed from original publication

Generated summary: A report follows Verlen Kruger and Steve Landick's long-distance canoe journey, including their progress through Alaska, winter plans, and fundraising appeal.

Open scan page 10

Read captured page 10 →

Twin Ports Chapter News

Title transcribed from original publication

Generated summary: A letter and chapter update describe the formation and first-year activities of the Twin Ports chapter, its members' varied canoeing interests, and plans to keep the group informal and accessible.

Open scan page 11

Read captured page 11 →

Why Do We Ignore Poling?

Title transcribed from original publication

Generated summary: George Skinner argues for renewed interest in canoe poling, recounts a trip on the St. Louis River, and describes his search for suitable equipment and instruction.

Open scan page 11

Read captured page 11 →

Cliff's Corner

Title transcribed from original publication

Generated summary: A first-person field review compares camp stove fuels and specific gasoline, kerosene, and other stoves, emphasizing reliability, operation, and suitability for canoe expeditions.

Open scan page 12

Read captured pages 12–13 →

Still on the Right Track

Title transcribed from original publication

Generated summary: An overview of the North Star Ski Touring Club describes its newsletter, meetings, trips, social activities, races, and the community benefits of club membership.

Open scan page 13

Read captured page 13 →

Camp Cookery

Title transcribed from original publication

Generated summary: A sample two-day menu plan gives meal suggestions and trail-food combinations for a four-person ski tour, with a note that a later installment will discuss reducing the cost of freeze-dried food.

Open scan page 14

Read captured page 14 →

Cruisin' Along

Title transcribed from original publication

Generated summary: The cruise director encourages members to lead canoe trips, explains the basic responsibilities of a trip leader, suggests rivers and trip formats, and invites members to propose cruises.

Open scan page 14

Read captured page 14 →

January Board Meeting

Title transcribed from original publication

Generated summary: A summary of the January board meeting lists planned monthly programs, reports on handbook and outreach efforts, and notes a membership dues increase and preparations for a ski challenge race.

Open scan page 15

Read captured page 15 →