← Back to The HUT

September 1973 · Volume/issue not printed or unknown

September 1973 Magazine

Issue first-page cover

Magazine · 16 pages

September 1973 Magazine

Captured text — scan page 12

Automatically captured text may contain recognition errors. Compare it with the original scan.

This shows the complete scan page, including any other material on it.

Plane the blade area for flatness and to re-
move excess glue. Glue and clamp handle

BS $
Tips on eee ae ee
before glueing.
] B
Paddle Building

by
Bill McArthur

Fig. 6

[ .
Laminated canoe paddles are easy to blade is about 13” wide by 15” long or \

build and with the cost of buyinga good — even a 13” round blade would work well. af}
one, making them is an attractive alterna-

tive. Very few tools are needed. Latch on

to someone with a table saw, get yourself

a can of good waterproof glue, a little The handle can then be built up, glued
spruce, a hand plane, and some sanding and clamped.

gear (an electric drill with sander is fine);

and you're ready to begin.

I made an edge glueing jig for use on
my workbench, with which two threaded
rods with wing nuts soldered on the end ;
apply the pressure to the edge of the
wos i=nn

' Fig. 7
2«2 CLAMP TO Fig. 3
BENCH 2x4 SLIDES ON
NUT \ Several handle styles are also used and Now you're ready for shaping and sanding.
any of these can be put on any of the
— BENCH TOP styles shown.
rec
Fig. 1 A Ag
In general, I like to make handles at ee

least 1” wide, 1 1/8” is real good and
about 1 1/8” to 1 1/4” thick. Blades can
be 1/4” or even 3/16” thick if glassed on
both sides, but remember there will be B-B

Co
A-A
some loss due to planing after glueing. I
like Sitka Spruce best for most stock. .
Cedar is okay but splinters easily when Fig. 8
stripping. I use cedar, mahogany or wal-

nut for accent color strips.
There are many blade shapes which

people like and any can be made in any Fig. 4
of the ways described below. The most is fairly easy on this design due to the
popular blade is about 8” wide x 18” to ; oo, square or flat edge. Use — strips or
24" long. The easiest method which gives a good strands of glass — unravelled roving or
paddle is as follows: Cut strips 1/4” thick ‘cloth does well. Wet the edge of the blade
and edge laminate, handle and blade. with resin and start to lay strands on the
1/4” edge. Saturate the strands as added.
After the first few strands, put a piece of
oversized wax paper on each side of the
blade to form a channel into which to lay
=a the strands. Continue building up until
Me ih 7 there is 1/8 - 1/4” of glass over the end
oA and corners of the blade and feather off

f up the sides as shown.

Next, I like to add fiberglass support
to the bottom edge and corners so the
paddle is not damaged on rocks. This step

Fig. 5

Fig. 2 I

I have made a banjo which I enjoy F
very much in shallow rocky streams. Its LA

10 HUT! SEPTEMBER 1973

Articles (7) · Summaries (7)

Generated issue overview: September 1973 issue of HUT!, the Minnesota Canoe Association magazine. The OCR supports seven articles on outdoor education, canoeing, conservation, paddle building, and canoe routes; the issue also includes staff and publication information, photographs, advertisements, and membership material.

Generated summaries are descriptions, not original captured text. Page-range text shows complete scan pages and may include neighboring material.

A Wilderness And Research Experience

Title transcribed from original publication

Generated summary: Describes Project AWARE, a Minneapolis high school course combining environmental study, student-directed work, and outdoor activities, including canoe trips in the Boundary Waters Canoe Area.

Open scan page 3

Read captured page 3 →

Canoeing in the Classroom

Title transcribed from original publication

Generated summary: Argues that schools should teach canoeing and other outdoor skills, explaining educational and environmental reasons for including outdoor recreation in the curriculum and encouraging community members to support such programs.

Open scan page 4

Read captured pages 4–5 →

The Thousand Waterways of Minnesota

Title transcribed from original publication

Generated summary: Surveys Minnesota canoeing, from challenging whitewater to family trips in the Boundary Waters and convenient routes near the Twin Cities. The article also describes regional history, geology, wildlife, and trip services.

Open scan page 6

Read captured pages 6–7 →

Western Whitewater

Title transcribed from original publication

Generated summary: Recounts a two-week trip on five western whitewater rivers—the Stillwater, Gallatin, Lochsa, St. Joe, and Flathead—and describes their conditions, scenery, and paddling challenges.

Open scan page 9

Read captured pages 9–10 →

Izaak Walton League Convention

Title transcribed from original publication

Generated summary: Reports on the Izaak Walton League's national convention, including discussion of timber wolf management, the Boundary Waters Canoe Area, conservation policy, and resolutions adopted by the organization.

Open scan page 11

Read captured page 11 →

Tips on Paddle Building

Title transcribed from original publication

Generated summary: Provides illustrated instructions for making laminated canoe paddles, describing materials, construction approaches, fiberglass reinforcement, shaping, and finishing.

Open scan page 12

Read captured pages 12–13 →

The Joe River

Title transcribed from original publication

Generated summary: Describes a little-traveled Everglades waterway, its wildlife and fishing, and practical route information for canoeists traveling between Flamingo and Mud Bay.

Open scan page 14

Read captured page 14 →